Improved Measurements of the Ice Water Content in Cirrus Using a Total-Water Probe

1995 ◽  
Vol 12 (2) ◽  
pp. 410-414 ◽  
Author(s):  
Philip R. A. Brown ◽  
Peter N. Francis
Keyword(s):  
Water Content ◽  
Total Water ◽  
Ice Water Content ◽  
Ice Water

Measurement of Total Water with a Tunable Diode Laser Hygrometer: Inlet Analysis, Calibration Procedure, and Ice Water Content Determination

2007 ◽  
Vol 24 (3) ◽  
pp. 463-475 ◽  
Author(s):  
Sean M. Davis ◽  
A. Gannet Hallar ◽  
Linnea M. Avallone ◽  
William Engblom
Keyword(s):  
Particle Size ◽  
Water Vapor ◽  
Water Content ◽  
Diode Laser ◽  
Tunable Diode Laser ◽  
Calibration Data ◽  
Total Water ◽  
Wide Range ◽  
Ice Water Content ◽  
Ice Water

Abstract The University of Colorado closed-path tunable diode laser hygrometer (CLH), a new instrument for the in situ measurement of enhanced total water (eTW, the sum of water vapor and condensed water enhanced by a subisokinetic inlet), has recently been flown aboard the NASA DC-8 and WB-57F aircrafts. The CLH has the sensitivity necessary to quantify the ice water content (IWC) of extremely thin subvisual cirrus clouds (∼0.1 mg m−3), while still providing measurements over a large range of conditions typical of upper-tropospheric cirrus (up to 1 g m−3). A key feature of the CLH is its subisokinetic inlet system, which is described in detail in this paper. The enhancement and evaporation of ice particles that results from the heated subisokinetic inlet is described both analytically and based on computational fluid dynamical simulations of the flow around the aircraft. Laboratory mixtures of water vapor with an accuracy of 2%–10% (2σ) were used to calibrate the CLH over a wide range of water vapor mixing ratios (∼50–50 000 ppm) and pressures (∼100–1000 mb). The water vapor retrieval algorithm, which is based on the CLH instrument properties as well as on the spectroscopic properties of the water absorption line, accurately fits the calibration data to within the uncertainty of the calibration mixtures and instrument signal-to-noise ratio. A method for calculating cirrus IWC from the CLH enhanced total water measurement is presented. In this method, the particle enhancement factor is determined from an independent particle size distribution measurement and the size-dependent CLH inlet efficiency. It is shown that despite the potentially large uncertainty in particle size measurements, the error introduced by this method adds ∼5% error to the IWC calculation. IWC accuracy ranges from 20% at the largest IWC to 50% at small IWC (<5 mg m−3).

scholarly journals A comparison of ice water content measurement techniques on the FAAM BAe-146 aircraft

2014 ◽  
Vol 7 (9) ◽  
pp. 3007-3022 ◽  
Author(s):  
S. J. Abel ◽  
R. J. Cotton ◽  
P. A. Barrett ◽  
A. K. Vance
Keyword(s):  
Water Content ◽  
Water Vapour ◽  
Measurement Techniques ◽  
Total Water Content ◽  
Total Water ◽  
Convective Clouds ◽  
Ice Particles ◽  
Mass Dimension ◽  
Ice Water Content ◽  
Ice Water

Abstract. This paper presents a comparison of ice water content (qi) data from a variety of measurement techniques on the Facility for Airborne Atmospheric Measurements (FAAM) BAe-146 research aircraft. Data are presented from a range of cloud types measured during the PIKNMIX field experiment that include mixed-phase stratocumulus, cumulus congestus and cirrus clouds. These measurements cover a broad range of conditions in which atmospheric ice particles are found in nature, such as the low-ice-water-content environments typically found in midlatitude cirrus and the environments with much higher ice water content often observed in cold convective clouds. The techniques include bulk measurements from (i) a Nevzorov hot-wire probe, (ii) the difference between the measured total water content (condensed plus vapour) and the water vapour content of the atmosphere and (iii) a counterflow virtual impactor (CVI) (only for cirrus measurements). We also estimate the qi from integration of the measured particle size distribution (PSD) with assumptions on how the density of ice particles varies as a function of size. The results show that the only bulk ice water content technique capable of measuring high qi values (several g m−3) was the method of total water content minus water vapour. For low ice water contents we develop a new parametrisation of the Nevzorov baseline drift that enables the probe to be sensitive to qi ± 0.002 g m−3. In cirrus clouds the agreement between the Nevzorov and other bulk measurements was typically better than a factor of 2 for the CVI (qi > 0.008 g m−3) and the method of total water content minus water vapour (qi > 0.02 g m−3). Good agreement with the bulk measurements for all cases could be obtained with the estimate from the PSD provided that appropriate a priori assumptions on the mass–dimension relationship were made. This is problematic in the convective clouds sampled because pristine ice particles, heavily rimed particles and supercooled liquid drops were all present. In a cirrus case, we show that using a temperature-dependent mass–dimension relation was required to match the bulk measurement of qi.

scholarly journals UARS/MLS Cloud Ice Measurements: Implications for H2O Transport near the Tropopause

2005 ◽  
Vol 62 (2) ◽  
pp. 518-530 ◽  
Author(s):  
D. L. Wu ◽  
W. G. Read ◽  
A. E. Dessler ◽  
S. C. Sherwood ◽  
J. H. Jiang
Keyword(s):  
Water Content ◽  
Total Water ◽  
Ice Clouds ◽  
Clear Sky ◽  
Ice Water Content ◽  
Satellite Microwave ◽  
Cold Point ◽  
Cloud Ice ◽  
Ice Water

Abstract A technique for detecting large hydrometeors at high altitudes is described here and applied to the Upper Atmosphere Research Satellite/Microwave Limb Sounder (UARS/MLS) 203-GHz radiance measurements at tangent pressures between 200 and 46 hPa. At these tangent pressures the radiances remain optically thin and cloudy-sky radiances are brighter than normal clear-sky cases. Unlike infrared/visible cloud observations, the 203-GHz radiances can penetrate most ice clouds and are sensitive to ice crystals of convective origin. Rough ice water content (IWC) retrievals are made near the tropopause using estimated size distributions from in situ convective studies. The seasonal mean IWC observed at 100 hPa reaches vapor-equivalent 20 ppmv or more over convective centers, dominating the total water content. Convectively lofted ice, therefore, appears to be hydrologically significant at the tropical cold point. IWC is well correlated spatially with relative humidity with respect to ice (RHi) at 100 hPa during both the dry (January–March) and moist (July–September) periods.

scholarly journals A two-channel, tunable diode laser-based hygrometer for measurement of water vapor and cirrus cloud ice water content in the upper troposphere and lower stratosphere

2015 ◽  
Vol 8 (1) ◽  
pp. 211-224 ◽  
Author(s):  
T. D. Thornberry ◽  
A. W. Rollins ◽  
R. S. Gao ◽  
L. A. Watts ◽  
S. J. Ciciora ◽  
...  
Keyword(s):  
Water Vapor ◽  
Water Content ◽  
Lower Stratosphere ◽  
Tunable Diode Laser ◽  
Cirrus Cloud ◽  
Total Water ◽  
Cloud Particle ◽  
Upper Troposphere ◽  
Ice Water Content ◽  
Ice Water

Abstract. The recently developed NOAA Water instrument is a two-channel, closed-path, tunable diode laser absorption spectrometer designed for the measurement of upper troposphere/lower stratosphere water vapor and enhanced total water (vapor + inertially enhanced condensed phase) from the NASA Global Hawk unmanned aircraft system (UAS) or other high-altitude research aircraft. The instrument utilizes wavelength-modulated spectroscopy with second harmonic detection near 2694 nm to achieve high precision with a 79 cm double-pass optical path. The detection cells are operated under constant temperature, pressure, and flow conditions to maintain a constant sensitivity to H2O independent of the ambient sampling environment. An onboard calibration system is used to perform periodic in situ calibrations to verify the stability of the instrument sensitivity during flight. For the water vapor channel, ambient air is sampled perpendicular to the flow past the aircraft in order to reject cloud particles, while the total water channel uses a heated, forward-facing inlet to sample both water vapor and cloud particles. The total water inlet operates subisokinetically, thereby inertially enhancing cloud particle number in the sample flow and affording increased cloud water content sensitivity. The NOAA Water instrument was flown for the first time during the second deployment of the Airborne Tropical TRopopause EXperiment (ATTREX) in February–March 2013 on the NASA Global Hawk UAS. The instrument demonstrated a typical in-flight precision (1 s, 1σ) of better than 0.17 parts per million (ppm, 10−6 mol mol−1), with an overall H2O vapor measurement uncertainty of 5% ± 0.23 ppm. The inertial enhancement for cirrus cloud particle sampling under ATTREX flight conditions ranged from 33 to 48 for ice particles larger than 8 μm in diameter, depending primarily on aircraft altitude. The resulting ice water content detection limit (2σ) was 0.023–0.013 ppm, corresponding to approximately 2 μg m−3, with an estimated overall uncertainty of 20%.

scholarly journals A two-channel, tunable diode laser-based hygrometer for measurement of water vapor and cirrus cloud ice water content in the upper troposphere and lower stratosphere

2014 ◽  
Vol 7 (8) ◽  
pp. 8271-8309 ◽  
Author(s):  
T. D. Thornberry ◽  
A. W. Rollins ◽  
R. S. Gao ◽  
L. A. Watts ◽  
S. J. Ciciora ◽  
...  
Keyword(s):  
Water Vapor ◽  
Water Content ◽  
Lower Stratosphere ◽  
Tunable Diode Laser ◽  
Cirrus Cloud ◽  
Total Water ◽  
Cloud Particle ◽  
Upper Troposphere ◽  
Ice Water Content ◽  
Ice Water

Abstract. The recently developed NOAA Water instrument is a two-channel, closed-path, tunable diode laser absorption spectrometer designed for the measurement of water vapor and enhanced total water (vapor + inertially enhanced condensed-phase) in the upper troposphere/lower stratosphere from the NASA Global Hawk unmanned aircraft system (UAS) or other high-altitude research aircraft. The instrument utilizes wavelength-modulated spectroscopy with second harmonic detection near 2694 nm to achieve high precision with a 79 cm double-pass optical path. The detection cells are operated under constant temperature, pressure and flow conditions to maintain a constant sensitivity to H2O independent of the ambient sampling environment. An on-board calibration system is used to perform periodic in situ calibrations to verify the stability of the instrument sensitivity during flight. For the water vapor channel, ambient air is sampled perpendicular to the flow past the aircraft in order to reject cloud particles, while the total water channel uses a heated, forward-facing inlet to sample both water vapor and cloud particles. The total water inlet operates subisokinetically, thereby inertially enhancing cloud particle number in the sample flow and affording increased cloud water content sensitivity. The NOAA Water instrument was flown for the first time during the second deployment of the Airborne Tropical TRopopause EXperiment (ATTREX) in February–March 2013 on board the Global Hawk UAS. The instrument demonstrated a typical in-flight precision (1 s, 1σ) of better than 0.17 parts per million (ppm, 10−6 mol mol−1), with an overall H2O vapor measurement uncertainty of 5% ± 0.23 ppm. The inertial enhancement for cirrus cloud particle sampling under ATTREX flight conditions ranged from 33–48 for ice particles larger than 8 μm in diameter, depending primarily on aircraft altitude. The resulting ice water content detection limit (2σ) was 0.023–0.013 ppm, corresponding to approximately 2 μg m−3, with an estimated overall uncertainty of 20%.

scholarly journals A comparison of ice water content measurement techniques on the FAAM BAe-146 aircraft

2014 ◽  
Vol 7 (5) ◽  
pp. 4815-4857 ◽  
Author(s):  
S. J. Abel ◽  
R. J. Cotton ◽  
P. A. Barrett ◽  
A. K. Vance
Keyword(s):  
Water Content ◽  
Water Vapour ◽  
Measurement Techniques ◽  
Total Water Content ◽  
Total Water ◽  
Convective Clouds ◽  
Ice Particles ◽  
Mass Dimension ◽  
Ice Water Content ◽  
Ice Water

Abstract. This paper presents a comparison of ice water content (qi) data from a variety of measurement techniques on the Facility for Airborne Atmospheric Measurements (FAAM) BAe-146 research aircraft. Data are presented from a range of cloud types measured during the PIKNMIX field experiment that include mixed phase stratocumulus, cumulus congestus and cirrus clouds. These measurements cover a broad range of conditions in which atmospheric ice particles are found in nature, such as the low ice water content environments typically found in mid-latitude cirrus and the much higher ice water content environments often observed in cold convective clouds. The techniques include bulk measurements from (i) a Nevzorov hot-wire probe (ii) the difference between the measured total water content (condensed plus vapour) and the water vapour content of the atmosphere and (iii) a Counterflow Virtual Impactor (CVI) (only for cirrus measurements). We also estimate the qi from integration of the measured particle size distribution (PSD) with assumptions on how the density of ice particles varies as a function of size. The results show that the only bulk ice water content technique capable of measuring high qi values (several g kg−1) was the total water content minus water vapour method. For low ice water contents we develop a new parametrization of the Nevzorov base-line drift that enables the probe to be sensitive to qi ± 0.002 g m−3. In cirrus clouds the agreement between the Nevzorov and other bulk measurements was typically better than a factor of two for the CVI (qi 0.01 g kg−1) and the total water content minus water vapour method (qi > 0.03 g kg−1). Good agreement with the bulk measurements for all cases could be obtained with the estimate from the PSD provided that appropriate a-priori assumptions on the mass–dimension relationship were made. This is problematic in the convective clouds sampled because pristine ice particles, heavily rimed particles and supercooled liquid drops were all present. In a cirrus case we show that using a temperature dependent mass–dimension relation was required to match the bulk measurement of qi.

Ice water content assessment in the single-, dual-, and triple-frequency radar scenarios

2021 ◽  
Vol 254 ◽  
pp. 112242
Author(s):  
Eugenio Gorgucci ◽  
Luca Baldini ◽  
Elisa Adirosi ◽  
Mario Montopoli
Keyword(s):  
Water Content ◽  
Content Assessment ◽  
Triple Frequency ◽  
Ice Water Content ◽  
Ice Water

scholarly journals Measuring ice- and liquid-water properties in mixed-phase cloud layers at the Leipzig Cloudnet station

2016 ◽  
Vol 16 (16) ◽  
pp. 10609-10620 ◽  
Author(s):  
Johannes Bühl ◽  
Patric Seifert ◽  
Alexander Myagkov ◽  
Albert Ansmann
Keyword(s):  
Water Content ◽  
Liquid Water ◽  
Mass Flux ◽  
Mixed Phase ◽  
Cloud Base ◽  
Doppler Velocity ◽  
Special Focus ◽  
Data Set ◽  
Ice Water Content ◽  
Ice Water

Abstract. An analysis of the Cloudnet data set collected at Leipzig, Germany, with special focus on mixed-phase layered clouds is presented. We derive liquid- and ice-water content together with vertical motions of ice particles falling through cloud base. The ice mass flux is calculated by combining measurements of ice-water content and particle Doppler velocity. The efficiency of heterogeneous ice formation and its impact on cloud lifetime is estimated for different cloud-top temperatures by relating the ice mass flux and the liquid-water content at cloud top. Cloud radar measurements of polarization and Doppler velocity indicate that ice crystals formed in mixed-phase cloud layers with a geometrical thickness of less than 350 m are mostly pristine when they fall out of the cloud.

Simultaneous Ice Water Content Measurements at Multiple Locations on the NASA DC-8 Aircraft During the 2018 HIWC RADAR Flight Campaign

2021 ◽  
Author(s):  
Lyle E. Lilie ◽  
Dan Bouley ◽  
Christopher P. Sivo ◽  
John W. Strapp ◽  
Thomas P. Ratvasky
Keyword(s):  
Water Content ◽  
Ice Water Content ◽  
Ice Water
Sign in / Sign up

Export Citation Format

Share Document